Quick Presets:
Beat Frequency (f_beat)
|f₁ - f₂|
0.10 Hz
Loudness pulses per second
Beat Period (T_beat)
1 / |f₁ - f₂|
10.00 s
Time between loud peaks
Resultant Amplitude
A₁ ± A₂
Max (Loud)
2.00
Min (Soft)
0.00
At Time t = 0.00s
Δφ = 0°
Constructive (In Phase)
Wave peaks align → Maximum loudness
Displacement vs. Time Graph
(Click or drag on graph to inspect any time t)
Individual Tuning Fork Waves (y₁ & y₂)
Fork 1 (f₁)
Fork 2 (f₂)
Resultant Superposition Wave at Ear (y = y₁ + y₂)
Resultant y
Envelope
Time t:
0.00 s
Phase Alignment Inspector
Both wave vectors point in the same direction (In Phase), adding together constructively.
🔊 Perceived Sound Loudness at t
100% (Max)
Soft / Silence (Destructive)
Loud Peak (Constructive)
Tuning Fork Parameters
Real-Time
1.10 Hz
0.50 Hz
2.75 Hz
5.00 Hz
1.00 Hz
0.50 Hz
2.75 Hz
5.00 Hz
1.00
1.00
0°
10 s
🎧 Audio Pitch Mapping
220.0 Hz & 220.1 Hz
Visual waves (0.5–5 Hz) are shifted into the audible range around 220 Hz while preserving the exact beat difference |f₁ - f₂| so you can hear the loudness rise and fall!
🎓
Exam Key Points
HKDSE Marking Scheme & Conceptual Breakdown
1. Qualitative Explanation of Beats (Superposition)
- Continuously Changing Phase Difference: Because the two tuning forks have slightly different frequencies (f₁ ≠ f₂), the phase difference between the two sound waves arriving at the listener's ear changes continuously with time.
- Constructive Interference (Loud): At moments when the two waves arrive in phase (crest meets crest), constructive interference occurs, producing a maximum resultant amplitude (A₁ + A₂) and a loud sound (e.g., at t = 0s and t = 10s in the default graph).
- Destructive Interference (Soft): Half a beat period later, the waves arrive in anti-phase (crest meets trough). Destructive interference occurs, producing a minimum resultant amplitude (|A₁ - A₂|) and a soft sound (e.g., at t = 5s).
- This periodic alternation between constructive and destructive interference causes the perceived loudness to rise and fall periodically.
2. Effect of Making Frequencies Closer Together
Beat frequency: f_beat = |f₁ - f₂|
Beat period: T_beat = 1 / f_beat = 1 / |f₁ - f₂|
- As the two frequencies are made closer together, the frequency difference |f₁ - f₂| decreases.
- Consequently, the beat frequency decreases (fewer loud-soft cycles per second), and the beat period (T_beat) increases (takes longer between consecutive loud peaks).
- Try it above: Drag f₁ from 1.10 Hz down to 1.05 Hz and watch the destructive node shift from t = 5s out to t = 10s (T_beat = 20s)!
1. 點解會聽到聲量「時大時細」(Beats 拍現象)?
- Phase difference(相位差)不斷變: 因為兩支音叉嘅 frequency 差少少(一個快少少、一個慢少少),兩道聲波去到你耳仔嗰陣,佢哋嘅 phase difference 會隨住時間不停改變。
- 「同相」變超大聲(Constructive interference): 當某啲時刻兩道波啱啱好 in phase(同相)(波峰撞波峰),就會發生 constructive interference(相長干涉),合成波嘅 amplitude 去到最大(A₁ + A₂ = 2,就好似幅圖 t = 0s 同 10s 咁),你就會聽到最大聲。
- 「反相」變超細聲(Destructive interference): 過多陣快嗰個波超前咗半個週期,兩道波變成 anti-phase(反相)(波峰撞波谷),發生 destructive interference(相消干涉),互相抵消晒(amplitude 跌到 0,好似 t = 5s 正中間縮埋一舊咁),你就會聽到最細聲。
- 就係因為「同相 → 反相 → 同相」不停週期性交替,所以聲量就會一陣大、一陣細!
2. 兩個 frequency 越嚟越接近,Beat period 會點變?
拍頻 Beat frequency: f_beat = |f₁ - f₂|
拍週期 Beat period: T_beat = 1 / |f₁ - f₂|
- 當兩個頻率越嚟越接近,即係 |f₁ - f₂| 變細,所以 beat frequency(拍頻)會減少(decreases)(一秒內「嗡、嗡」閃動嘅次數少咗)。
- 因為週期同頻率成反比(T = 1/f),拍頻細咗,兩次最大聲之間隔嘅時間就會拉長,所以 beat period(拍週期)會變大 / 變長(increases)!
- 即刻試玩: 試下將上面 f₁ 由 1.10 Hz 推落去 1.05 Hz,你會見到中間個「縮細位」即刻由 t = 5s 拉長去 t = 10s(即係 T_beat 變咗 20s)!